Drapes & Sheers

3 FINGER FRENCH PLEAT
3 FINGER PINCH PLEAT TACK TOP & BOTTOM
GOBLET PLEAT
INVERTED PLEAT
ONLY FOR PINCH PLEAT (2 FINGER/3 FINGER)
  • Leading edge size: 2” for one-way draw. 4” for pair panels.

  • Standard fabrics: 2x fullness (not applicable for Ripplefold style).

  • Sheer fabrics: 3x fullness (not applicable for Ripplefold style).

  • Privacy lining is standard for draperies.

  • Returns sizes are available from 0” – 7”.

  • Standard return is 4”.

  • Only pre-sized pin position available.

  • Ceiling: 1¼” (down from top).

  • Traverse rod: 1¾” (down from top).Decorative rod: ½” (down from top).

  • Decorative rod: ½” (down from top).

PINCH PLEAT (L3-DR01), GOBLET (L3-DR05), INVERTED (L3-DR06)

3 FINGER PINCH PLEAT TACK TOP
  • Pinch Pleat top can choose 3 sizes: 3”, 4”, 6”.

  • Pinch Pleat tack position can be: top; bottom; top & bottom.

  • Goblet & Inverted Pleat are made with a 4” top.

  • Can be ordered as a pair, one-way draw, or stationary.

  • Provide precise width to cover up to 196”.

RETURNS
  • Return sizes: from 0” – 7”, with ½” increments.

  • Only Pinch Pleat style can be ordered with returns, all other styles are made with no returns.

  • For appropriate return size, state bracket projection of the hardware.

TWO-TONED DRAPES
  • Two fabrics combined with a horizontal seam.

  • Aspects to consider: Horizontal seam location (please provide measurement going from the bottom part of the panel to the top).

  • For better appearance, select fabrics to be combined that have similar weights.

  • Not available for sheer fabrics.

HOUR GLASS PANELS
TIEBACKS
  • Drapery panels can be pulled back with L3 tiebacks.

  • Offered in contoured & flat styles.

  • 3 sizes available (either as a pair or as 1 piece):

    • 23”

    • 34”

    • 45”.

  • Contoured tiebacks width:

    • From edge: 3½”

    • From center: 5½”

  • ​Flat tiebacks are offered in 3½” width only.

  • A cord or fringe may be added to a tieback as an option (sold separately).

GROMMET PANELS

For length:
Take measurements from the left, center & right of the window frame, always staying on the outside edge .

Add 10” total (5” to each side) to window´s edge width; this will allow more exterior light to come in when the drapery panels are fully opened.

WIDTH

HOW TO MEASURE FOR DRAPERIES

LENGTH
FOR ROD POCKET STYLE
FOR GROMMET STYLE

Length = top from the inside diameter of the grommet to the bottom.

Please provide length measurement with ½” accuracy. 

Puddle length drapery panels should rest 6” – 10” on the floor.

Floor length drapery panels should stay ½” above the floor.

Go to drapery hardware to choose the hardware style you will hang your drapery panels on. 

Note: besides grommet, tab top & rod pocket styles, final length may be affected depending on the hardware chosen; take this into consideration when selecting a style from the drapery hardware section.

RINGS:

Go to drapery hardware to choose the hardware style you will hang your drapery panels on. 

Eyelet adds 2” to final drapery panel length.

Eyelet & clip add 3” to final drapery panel length.

FOR SHEER UNDER TREATMENTS

When both drapery panel and sheer under treatment are hanging, the sheer panel should not be visible:
Sheer´s decorative hardware should be mounted 1” lower than 

The outer panel´s decorative hardware.
Sheer under treatment should be ½” shorter than the fabric 

The outer panel´s decorative hardware.
Sheer under treatment should be ½” shorter than the fabric

No Header Needed 

2 FINGER FRENCH PLEAT
DECORATIVE TRIMMINGS
  • Please see Decorative Trims & Accessories on page 48 for available accents and colors for your drapes.

RIPPLE FOLD &
TRACK SYSTEM
ROD POCKET PANELS
EDGE ACCENTS BANDING "Banding options"
  • Along fabrics edge.

  • Inset 2” from edge.

  • Placement:

    • Vertical on the leading edge.

ROD POCKET PANELS - L3-DR02
  • Single panel or a pair.

HEADER OPTIONS
  • Along with ¾” (max.) Diameter rod.

  • 1½” pocket / 1½” header.

  • 1½” pocket / no header.

FOR DECORATIVE RODS
  • Along with 1¼” (max) diameter decorative / 2 ½” basic rod:

  • 3” pocket / 3” header.

  • 3” pocket / no header.

  • Provide precise width to cover up to 196”.

TRADITIONAL TAB TOP
TRADITIONAL TAB TOP - L3-DR08
  • Single panel or pair.

  • 4”L x 2”W tabs spaced approximately 9” from tab center to next tab center.

  • Tab height is included on the final height of the drapery.

  • Provide precise width to cover up to 196”.

  • Single panel or pair.

  • Minimum 200% fullness.

  • Grommets are offered in 4 finishes.

GROMMET PANELS -
L3-DR07
SIZES
  • Outer diameter: 2½”; inner diameter: 1½” .

RODS & POLES
  • Maximum diameter available for this style: 1¼”.

  • Provide precise width to cover up to 196”.

BACK TAB PANELS
HOUR GLASS PANELS - L3-DR09
  • Single panel or a pair.

HEADER OPTIONS
  • Along with ¾” (max.) Diameter rod .

  • 1½” pocket / 1½” header.

  • 1½” pocket / no header.

FOR DECORATIVE RODS
  • Along with 1 ¼” (max) diameter decorative/2 ½” basic rod:

    • 3” pocket / 3” header.

    • ​3” pocket / no header.

  • Provide precise width to cover up to 48”.

  • 1 flat tieback per panel is included.

BACK TAB PANELS - L3-DR10
  • Single panel or a pair.

  • 4”L x 2”W tabs spaced approximately 9” from tab center to next tab center.

  • Provide precise width to cover up to 196”.

RIPPLE FOLD & TRACK SYSTEM - L3-DR11
  • Single panel or pair.

  • Single: provide precise width to cover up to 144”.

  • Pair: provide precise width to cover up to 240”.

  • 180% fullness.

  • Batons included.
    NOTE: ¼” Gap between the drapery panel and track system.

  • Metal snap attached to top of drapery panels; may be seen especially on sheer draperies.

RING TOP PANELS - L3-DR12
  • Single panel or pair.

  • Rings are sewn to the top section of the panels.

  • Use L3 decorative hardware to complement any drapery application.

  • Ring height is included on the final height of the drapery.

  • Provide precise width to cover up to 196”.

STANDARD SPECIFICATIONS FOR DRAPERY

  • Panels are unlined – lining options available.

  • Side hems are 1”.

  • Fabric bottom hem is 4”.

  • Lining bottom hem is 1”.

  • Lining length will be 2” shorter than fabric length.

  • Products made with the same fabric MUST be made with the same lining.

MOTORIZED DRAPERIES
  • Only available for Pinch Pleat & Ripplefold styles.

STANDARD SPECIFICATIONS
  • Somfy® Motor System.

  • A/C (plug-in) power motors only.

  • One-way motors are positioned on the stack side of the drapery panel.

  • For pairs of drapery panels, motor location must be specified on the order, (left or right side).

CONTROLS
  • Remote control 4 channel.

  • Wall switch 4 channel.

A/C
  • A power cord is standard and plugs into a standard wall outlet. 

STACKING SPACE
  • The motor adds approximately 6-8” to the drapery´s stacking dimensions.

NOTES
  • When filling out the order form, be sure the multiple draperies measurements are recorded in one room in sequence, from left to right. The workroom will pre-program the remote control in that sequence. One remote control/remote switch for every 4 draperies.

SIZE LIMITATIONS FOR ALL STYLES*
Tel: 844-521-8048

© 2016 BY LEVEL 3 INDUSTRIES. ALL RIGHTS RESERVED.